Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

基于平均飞行航迹的CCO减噪效用研究

近年来，通过优化飞行程序降低机场飞机噪声影响成为机场环境保护的重要研究方向。文章首先建立了基于飞机“噪声-功率-距离”数据的噪声计算模型，介绍了平均飞行航迹以及连续爬升运行(Continuous Climb Opera-tion, CCO)离场程序的相关理论，最后以大型国际机场为实例，使用飞机平均飞行航迹进行噪声预测，运用综合噪声模型计算出噪声影响面积并绘制噪声影响等值线图，比较了CCO离场相对常规的标准仪表离场(Standard Instru-ment Departure, SID)的降噪效果。结果表明，CCO离场程序可有效降低机场噪声影响，在高噪声级影响区域的降噪效果更佳。     

A Smart Deep Convolutional Neural Network for Real-Time Surface Inspection

A proper detection and classification of defects in steel sheets in real time have become a requirement for manufacturing these products, largely used in many industrial sectors. However, computers used in the production line of small to medium size companies, in general, lack performance to attend real-time inspection with high processing demands. In this paper, a smart deep convolutional neural network for using in real-time surface inspection of steel rolling sheets is proposed. The architecture is based on the state-of-the-art SqueezeNet approach, which was originally developed for usage with autonomous vehicles. The main features of the proposed model are: small size and low computational burden. The model is 10 to 20 times smaller when compared to other networks designed for the same task, and more than 700 times smaller than general networks. Also, the number of floating-point operations for a prediction is about 50 times lower than the ones used for similar tasks. Despite its small size, the proposed model achieved near-perfect accuracy on a public dataset of 1800 images of six types of steel rolling defects.     

Influence of pressure and dwell time on pressure-assisted sintering of calcium cobaltite

Calcium cobaltite Ca₃Co₄O₉, abbreviated Co349, is a promising thermoelectric material for high-temperature applications in air. Its anisotropic properties can be assigned to polycrystalline parts by texturing. Tape casting and pressure-assisted sintering (PAS) are a possible future way for a cost-effective mass-production of thermoelectric generators. This study examines the influence of pressure and dwell time during PAS at 900°C of tape-cast Co349 on texture and thermoelectric properties. Tape casting aligns lentoid Co349. PAS results in a textured Co349 microstructure with the thermoelectrically favorable ab-direction perpendicular to the pressing direction. By pressure variation during sintering, the microstructure of Co349 can be tailored either toward a maximum figure of merit as required for energy harvesting or toward a maximum power factor as required for energy harvesting. Moderate pressure of 2.5 MPa results in 25% porosity and a textured microstructure with a figure of merit of 0.13 at 700°C, two times higher than the dry-pressed, pressureless-sintered reference. A pressure of 7.5 MPa leads to 94% density and a high power factor of 326 µW/mK² at 800°C, which is 11 times higher than the dry-pressed reference (30 MPa) from the same powder.     

Tuning of shear thickening behavior and elastic strength of polyvinylidene fluoride via doping of ZnO-graphene

ZnO rice like nonarchitects are grafted on the graphene carbon core via a rapid microwave synthesis route. The prepared grafted systems are characterized via XRD, SEM, RAMAN, and XPS to examined the structural and morphological parameters. Zinc oxide grafted graphene sheets (ZnO-G) are further doped in β-phase of polyvinylidene fluoride (PVDF) to prepare the polymer nanocomposites (PNCs) via mixed solvent approach (THF/DMF). β-phase confirmation of PVDF PNCs is done by FTIR studies. It is observed that ZnO-G filler enhances the β-phase content in the PNCs. Non-doped PVDF and PNCs are further studied for rheological behavior under the shear rate of 1–100 s⁻¹. Doping of ZnO-G dopant to the PVDF matrix changes its discontinuous shear thickening (DST) behavior to continues shear thickening behavior (CST). Hydrocluster formation and their interaction with the dopant could be the reason for this striking DST to CST behavioral change. Strain amplitude sweep (10⁻³% -10%) oscillatory test reveals that the PNCs shows extended linear viscoelastic region with high elastic modulus and lower viscous modulus. Effective shear thickening behavior and strong elastic strength of these PNCs present their candidature for various fields including mechanical and soft body armor applications.     

铌对取向硅钢冷轧组织织构的影响

采用光学显微镜(OM)、电子背散射衍射(EBSD)等研究了铌对取向硅钢冷轧过程中的组织与织构的影响。结果表明:含铌正火板和不含铌正火板经冷轧后都是条带状组织,但含铌冷轧板在宽度方向更窄。铌元素的存在对织构也具有优化作用,经过中间退火后,含铌冷轧板二次冷轧织构得到明显改善,相较于不含铌二次冷轧板拥有强度较低的旋转立方织构以及强度较高的{111}<112>织构,其取向密度最高可达12.460。     

面向连续查询的敏感语义位置隐私保护方案

针对连续查询位置服务中构造匿名区域未考虑语义位置信息导致敏感隐私泄露问题，通过设计[(K,θ)]-隐私模型，提出一种路网环境下面向连续查询的敏感语义位置隐私保护方案。该方案利用Voronoi图将城市路网预先划分为独立的Voronoi单元，依据用户的移动路径和移动速度，选择具有相似特性的其他[K-1]个用户，构建匿名用户集；利用匿名用户集用户设定的敏感语义位置类型和语义安全阈值，以及用户所处语义位置的Voronoi单元，构建满足[(K,θ)]-隐私模型的语义安全匿名区域，可以同时防止连续查询追踪攻击和语义推断攻击。实验结果表明，与SCPA算法相比，该方案在隐私保护程度上提升约15%，系统开销上降低约20%。     

低活化马氏体钢热变形行为及机理型本构建模研究

利用Gleeble-3500热模拟试验机研究了低活化马氏体钢在变形温度为850～950 ℃、应变速率为0.001～1 s^-1条件下的热变形行为。建立了流变应力本构方程，并评估了该方程的预测能力。绘制了低活化马氏体钢在不同应变下的热加工图。结果表明：在较高的应变速率条件下，该材料主要发生动态回复，在较高变形温度和较低应变速率下具有明显的动态再结晶特征；本构方程的预测结果与实验结果符合良好；变形温度870～930 ℃、应变速率0.001～0.01 s^-1和变形温度920～950 ℃、应变速率0.3～1 s^-1分别是真应变为0.4和0.6下最优的热加工区域。     

基于改进奇异值分解滤波和谱峭度的滚动轴承故障诊断

针对含噪信号的有效奇异值个数难以确定的问题，提出了一种改进的奇异值分解降噪方法--奇异值累积法。该方法通过计算奇异值的实际下降值与奇异值平均下降速度累积量的差值，并取该差值最大值点的位置作为有效奇异值的分界点来确定有效奇异值的个数。在此基础上，提出了一种基于奇异值累积法与快速谱峭度的滚动轴承故障诊断方法。采用奇异值累积法对原信号进行降噪处理，然后利用快速谱峭度确定滤波器中心频率及带宽，通过分析频段包络谱中明显的频率成分来诊断故障。该方法可以有效去除信号中的噪声，使得到的峭度值所反映的故障冲击更接近实际情况。对含内圈、外圈故障的滚动轴承实验数据进行分析，实验结果表明，相比快速谱峭度的故障诊断方法，该方法具有更好的故障识别效果。     

整体壁板离散填料滚弯成形有限元模拟

具有一定曲率外形的铝合金整体壁板属于典型的多筋零部件,传统弯曲成形工艺成形困难,容易产生多种缺陷。提出了离散填料辅助滚弯成形整体2A12T4铝合金壁板滚弯工艺,并通过实验与整体填料滚变成形进行了对比,同时采用有限元模拟技术,探究了离散填料辅助整体壁板滚弯成形中的影响因素。研究结果表明:填料数量、上下垫板厚度等因素对成形性能影响较大,填料在3~6块时成形稳定,可以有效地避免筋条屈曲与失稳;随垫板厚度增加,壁板表面圆弧更加光滑、连续,但是回弹性增强;上下垫板分别在10~20 mm厚度时,综合性能较好。通过离散填料辅助滚弯技术可以成形出质量较高的整体壁板。